page_banner

products

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi

Short Description:


Product Detail

Product Tags

Related Video

Feedback (2)

The customer satisfaction is our primary goal. We uphold a consistent level of professionalism, quality, credibility and service for Laminated Glass With Fabric Interlayer, Pvb Sheet, testkewords, Teamwork is encouraged at all levels with regular campaigns. Our research group experiments on various developments during the industry for improvement within the solutions.
Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi Detail:

Thermo cutter Introduction

Thermo cutter or Heating cutter is a professional hot cutting tool for Fabrics and Plastic. It can up in seconds and gives the operator temperature control. Never before has working with Fabrics been this easy. inexpensive and free of mess. The 7-0 heating cutter is the First  Knife with Air-cooling System in the world. It can continuously operated with 2 times faster than all of existing hot cutting tools.

Operating instruction

Please read this instruction carefully before operation, take special care on safety prompts in these instructions so as to avoid injury to yourself. other people and objects. Please follow the guidelines in these instructions to avoid damage to the tool.

Recommended Use

Fabrics, Fiberglass Fabrics and Polyester Fabrics can be easily cut with the thermo cutter.

Blade Installation

NOTE: Always unplug the power cord of the cutter(Knife) before installing or removing the blades. Allow sufficient cooling time for blades, blade holders and mounting crews before handing.

Caution 1: The blade have a sharpened razor edge, for the cleanest cut always cut in the direction on the sharpened edge.

STRAIGHT BLADE:

1. Loosen the screws on the blade holders with the wrench.

2. Slide the blade under the square pressure plates until snug

3. Securely tighten screws to assure the proper electrical connection. Do not over-tighten

4. Once the blade is firmly in place, plug the heating cutter Unit into a standard 230/110volt power supply.

5. The temperature control knob has 16 click setting that correspond to the graduated ridges on the surface. The smaller the ridge the lower the power setting.

Caution 2: Excessive power output and heat generation may cause the blade holders to overheat resulting in damage to the unit. Use only the power output for proper cutting. The blade does not need to be red hot to move through foamed plastics.

Operation

Put your temperature control knob at mid-range setting, place the blade against the edge of the fabric and depress trigger. Optimum cutting should be virtually smoke free.

NOTE: For the best results, practice on scrap pieces of Fabric. When cutting it is best to keep the temperature and speed consistent. If smoke develops during the cut, you are cutting too slow or the blade is too hot which could result in an oversized, uneven cut. This can be remedied by lowering the temperature and intermittently releasing the trigger during your cut. As the cutting resistance increases, depress the trigger again. The 7-0 Hot Knife will reach the set temperature within seconds. You can accomplish your cut with minimal smoke using this process. Cutting in this manner will also prolong the life of the knife.

Releasing the trigger approximately one or tow inches prior to the completion of the cut will help keep the blade clean and free from buildup

Caution 3:

1. Always operate the  Thermo cutter ( Hot Knife) in well ventilated space

2. Never burn off excess residue on the hot knife blade. The blades will overheat, warping the blade and potentially overheating the  Thermo cutter ( Hot Knife)

3. Only operate Thermo cutter ( Hot Knife) when it is in contact with the insulation board.

4. Keep hot blades away from skin, clothing and other flammable materials.

Allow blades to cool before handling. A hot blade may cause injury or burns to exposed surfaces.

Maintenance

Constant use of the 7-0 Hot Knife may result in some material build up on blades and the brass holders. This excess material interferes with the proper electrical and impairs the performance of the blades. The brass blade holder sand blades can be thoroughly cleaned with a wire brush

Specification

INPUT: 230/110 Volts

OUTPUT:Max. 100 Watts

Continuously Operation is workable

WEIGHT: 450 g

BODY LENGTH:290mm

Max TEMPERATURE:400C

Basic Kit

Hot Knife Handle*1

Wire brush*1

Special spanner *1

Carton box (Tool box)*1


Product detail pictures:

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi detail pictures

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi detail pictures

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi detail pictures

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi detail pictures

Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi detail pictures


Related Product Guide:

We keep on with the theory of quality first, provider initially, constant improvement and innovation to meet the customers with the management and zero defect, zero complaints as the standard objective. To great our company, we deliver the merchandise using the fantastic excellent at the reasonable price for Factory wholesale Eva Interlayer Film For Laminated Glass - Thermo cutter – Xiaoshi , The product will supply to all over the world, such as: Buenos Aires, Paris, Paraguay, We supply professional service, prompt reply, timely delivery, excellent quality and best price to our customers. Satisfaction and good credit to every customer is our priority. We focus on every detail of order processing for customers till they have received safe and sound products with good logistics service and economical cost. Depending on this, our products are sold very well in the countries in Africa, the Mid-East and Southeast Asia. Adhering to the business philosophy of ‘customer first, forge ahead', we sincerely welcome clients from at home and abroad to cooperate with us.
  • Goods just received, we are very satisfied, a very good supplier, hope to make persistent efforts to do better.
    5 Stars By Athena from India - 2018.04.25 16:46
    The factory workers have a good team spirit, so we received high quality products fast, in addition, the price is also appropriate, this is a very good and reliable Chinese manufacturers.
    5 Stars By Katherine from Danish - 2017.10.13 10:47
    Write your message here and send it to us